The CONVERGE® Pro 2 120 is an advanced multi-channel microphone auto mixer with the latest audio DSP algorithms, from ClearOne. This mixer adds Twelve (12) configurable mic/line audio inputs and built-in USB audio in an installation, and adds a powerful Digital Signal Processor.

Image shown above is for illustrative purposes only; actual product appearance may vary.

ClearOne 910-3200-004 Includes:

• (1) 6’ Grounded Power Cord
• (12) Orange 3 Position Terminal Block Input Connectors
• (1) Green 6 Position Terminal Block GPIO Connector
• (1) 18” RJ-45 To RJ-45 C-Link Cable
• (1) 6’ USB Type A to Type B Cable
• (2) Pre-installed Rack Ears
• Rack Decor Screw/Washer Kit

ClearOne 910-3200-004 Features:

• 12 mic/line inputs
• USB audio
• C-Link and P-Link enable addition of DSPs and peripherals
• Flexible control options include Touch Panel Controller, BYOD dialer apps or 3rd party control modules
• Configure an entire system of C-linked DSPs with CONSOLE AI software
• Built-in DARE™ algorithm for dynamic feedback elimination
• Connect via C-link to VoIP and Telco enabled DSPs for conferencing
• Reduced foot-print and power consumption

ClearOne 910-3200-004 Specifications:

• MIC/LINE INPUTS
  • Inputs:
    • Balanced audio inputs
    • 3.81mm Orange color Phoenix/Euroblock type male header
    • Push-on mini-terminal block
  • Frequency Response: 20Hz – 22kHz @ +4dBu, +/- 0.5dBu
  • EIN (Equivalent Input Noise): 20kHz BW, max gain, Rs = 150Ω, -126dBu
  • THD + N (Total Harmonic Distortion + Noise):
    • 20Hz – 22kHz @ +4dBu, line level, 0.006%
    • 20Hz – 22kHz @ -56dBu, mic level, < 0.04%
  • Dynamic Range: 20Hz – 20kHz @ 0dB, > 105dB
  • Crosstalk (Mic/Line): Channel to Channel, stimulus at 20dBu to receptor at -56dBu, 1kHz, < -98dB
  • Input Impedance: Balanced (line to ground), 2.2kΩ, 1%
  • Maximum Input Level: -65dBu to 20dBu
  • Phantom Power: 48V, Impedance 6.81kΩ
• USB AUDIO
  • Port Type: USB-B connector
  • Audio: Digital Audio, 2 x 2 bidirectional channels
  • Compatible:
    • USB 2.0
    • USB 3.0
  • Sample Rate: 48kHz
  • Sample Bit Depth: 24-Bit
• ETHERNET
  • Port Type: RJ-45, 10/100Mbps Ethernet Network, Auto Negotiation
  • IP address: IPv4 (IPv6 upgradeable through future s/w, f/w upgrade)
• C-LINK EXPANSION BUS
  • Ports Type: RJ-45 (Cat5e or Cat6)
  • C-Link In & Out: Proprietary Expansion Bus
  • Audio: 64 Expansion channels
  • Cable: Solid core, factory terminated Cat 5e or 6 cable
  • Distance: Up to 150’ (45M)
• P-LINK PERIPHERAL BUS
  • Ports Type: RJ-45 (Cat5e or Cat6)
  • P-Link In & Out: Proprietary Peripheral Bus
  • PoE In:
    • P-Link In Port
    • PoE 802.3af Mode B, Midspan
    • Power on “spare pairs” 4,5 and 7,8
  • Input voltage range: 48V to 56V
  • Audio: Up to 3 Beamforming Microphone Array 2 units + up to 3 DIALOG 20 Wireless Receiver units + Up to 3 USB Expander units + Up to 3 GPIO Expander units
  • Cable: Solid core, factory terminated Cat 5e or 6 cable
  • Distance: Up to 200’ (60M)
  • Long Distance P-Link:
  • Increases P-Link distance from 200 Ft to 650 Ft
  • 650 Ft (200M) maximum cable distance between any two units
  • Cat6, 550 MHz, 23 AWG, solid conductor cable
  • Do not use Copper Clad Aluminum (CCA) cable
  • Available only for BFM2 peripheral units
  • 48V PoE Midspan Mode B power injector for 1 BFM2 unit
  • 56V PoE Midspan Mode B power injector for 3 BFM2 units
• RS232
  • Port Type: DB9 Female
  • Settings: 9600/19200/38400/57600/115200 Baud; Serial Echo; Flow Control
  • Support: Serial commands
• GPIO
  • Port Type: 5.08mm Green color Phoenix/Euroblock type male header
  • Support: Control, Status, Variable Voltage Control
  • Power Pin: 5V DC @ 350mA Power Source
  • Pin 1 to 4:
    • Open Collector Outputs: 40VDC @ 250mA
    • Active Outputs (Source/Sink): 5VDC @25mA
    • Logic Inputs: 40.2kΩ pull up
    • Variable Voltage Control Inputs: 5VDC max
  • Ground Pin: GND
• USB CONTROL
  • Port Type: USB-B connector
  • Compatible:
    • USB 2.0
    • USB 3.0
  • Location: Front Panel
• LEDs
  • Location: Front Panel
  • Status LED:
    • Off: Unit still initializing
    • Blue - Fast Blinking: Stack Syncing in progress
    • Blue - Slow Blinking: Unit not configured
    • Blue - Solid: Configured unit
    • Red - Fast Blinking: Stack Sync error
  • Locate LED: Blue - Blinking: Unit “Locate” command received
  • Power LED: Blue - Solid: Unit is powered on
• TOUCH SENSOR
  • Sensor Type: Capacitive Touch Button
  • Location: Front Panel
• POWER & THERMAL
  • Port Type: AC Inlet
  • Mains Voltage: 100-240V AC, 50/60Hz
  • Power Consumption: 50 Watts Typical
  • Thermal: 170 BTU/Hr Typical
  • Ambient Operating Temperature: 14°F to 104°F (-10°C to 40°C)
• DIMENSION & WEIGHT
  • RU size: 1 RU
  • Dimensions (WxDxH):
    • Without rack-ears: 17” x 10.73” x 1.72” (43.2 x 27.3 x 4.4 cm)
    • With rack-ears: 19” x 10.73” x 1.72” (48.3 x 27.3 x 4.4 cm)
  • Unit Weight (Approx.): 9.3 lbs (4.2 kg)
  • Shipping Weight (Approx.): 13.8 lbs (6.3 kg)